[Author: Scott Wiggins *]
How many of you are completely terrified of doing anything to the mix buss, aka “stereo buss” “2 buss”?
It is real easy to mess up an entire mix with too much processing, in particular, mix buss compression.
Over the years of searching the internet creeping on my favorite mixers (Jaquire King, Dave Pensado, Chris Lord Alge, and many more) mix buss compression settings I’ve found that a little goes a long way.
Mix Buss Compression Glue
Have you ever heard the term “glue” in a conversation of recording and mixing?
No, I’m not talking about the kind you used to put on your hands in elementary so you could peel it off when it dried.
Am I the only one who did that?
I’m talking about the way compression can make tracks seem like they fit together a little better.
When set up correctly it makes the whole song feel like it’s glued together in the subtle ways which gives it a nice musical polished cohesive sound.
The goal with mix buss compression would be to just tame any transients that may spike up in volume just a little too much, and then bring the overall volume up of the rest of the tracks juuuuuust a bit.
We’re just trying to add a little more energy and fullness to the mix.
Mix Buss Compression Settings
The attack setting you use for mix buss compression is important just like using a compressor on any other track.
With a faster attack the compressor will clamp down sooner on the transients that tend to be a little louder than the rest of the audio coming through.
A slower attack will wait milliseconds before it clamps down on the audio and starts compressing.
I tend to use a faster attack, BUT I’m not crushing those transients with a ton of compression, so I still keep the dynamics in my mix.
If I found I was killing the transients too much and there was no excitement in my mix, I would probably make it a slower attack setting.
I tend to use a medium to fast release setting.
I’ve heard a lot of famous mixers say they set the release with the tempo of the song.
So they would watch the gain reduction needle and have it release on beat with the song.
I try my best to use this method.
I use a really small ratio of around 1.5 to 1.
This means that once my audio passes the threshold I’ve set that there is very little compression happening to that audio.
It’s just a little bit. I’m not trying to squash the life out of it.
You can experiment with a little bit higher of a ratio, but know that the lower the ratio the less compression (more dynamics), and the higher the ratio the more compression (less dynamics).
I dial the threshold to where I’m only getting about 1 to 3 dbs of gain reduction on the peaks of the audio.
I tend to keep it on the lower side of 1 to 2 dbs of gain reduction.
You just want to kiss the needle. You don’t want to have to much mix bus compression happening.
Remember, we are going for a subtle “glue” like affect.
Make up Gain:
Just like on any other compressor, I turn the make up gain to math the amount of gain reduction happening.
Be careful here. Don’t turn it up to loud and fool yourself that you like the result just because it’s louder.
Do your best to math the input volume with the output volume of the compressor.
We tend to think louder is better when it’s not really better, it’s just louder.
I’ve shot a video tutorial below to show all of this in action on a mix i’ve started. Check it out!
Mix buss compression is a great way to add a little bit of excitement and glue to your mix.
Some people like to slap it on the master buss AFTER they have mixed it (Ryan West who’s credits are Jay-Z, Eminem, Kid Cudi, Maroon 5, T.I, Rihanna and Kanye West)
And some engineers like to slap a little bit of compression on in the beginning and mix through it.
I don’t think there is a right or wrong way when it comes to when to put it on.
The key is to be subtle and don’t kill a good mix with too much mix buss compression.
Use your ears like always. They are your biggest weapons.
Good luck and happy mixing!
If you want to learn the 1st step to a successful mix even before you think about adding mix buss compression, check this post out about “The Static Mix”.
[Editors Note: This is blog was written by Scott Wiggins and it originally appeared on his site, The Recording Solution, which is dedicated to helping producers, engineers and artists make better music from their home studios.]